orbis-reframe Manual Camera formats Download Source code

The manual of orbis-reframe 0.10.1, the newest release. What has changed since is in the development version on GitHub.

Audio and noise reduction

This page covers the sound of your video: the camera's own microphones, music and other audio files, volume and fades, and taking out wind and other noise. How to add, move, trim and split audio clips on the timeline is in The timeline.

Where the sound comes from

Everything plays together, in playback and in the export.

The Audio tab

The settings sidebar's Audio tab shows audio clips, one section per clip, titled with the clip's track. Which clips depends on what's selected, and each section's title row says which (This clip, Selected PiP clip or Selected audio clip):

With none of these, the tab says what to select. For a clip with no sound -- from a camera that records none, or one whose sound you deleted from the timeline -- it says No sound; the clip is silent in playback and export.

The Audio tab for a video clip's sound The Audio tab for a music clip on an audio track

Left: a video clip's sound. Right: a music clip on an audio track.

Click a section's title to fold it away or open it again; orbis-reframe remembers this for each kind of track. Each section has:

Setting What it does
Clip The clip's file name.
Noise and Strength Noise reduction, see below.
Track level and Mute track The volume of the whole track the clip is on, on top of each clip's own level, and muting it.
Level and Mute This clip's own volume, from −24 dB to +12 dB, and muting it. 0 dB leaves it as recorded; negative values make it quieter, positive values louder.
Fade in / Fade out Fades the clip in from silence at its start, or out to silence at its end, over this many seconds. The fades show as slanted lines over the clip's waveform. At a transition, a video clip's own sound fades with the picture instead: crossfading with the next clip's, or out and in at a dip to black (where a longer fade of its own wins).
Start Where the clip starts on the timeline, in seconds. The arrows move it by 10 milliseconds, for lining up a separate recorder with the picture (see below). Greyed out for a linked clip, which moves with its video.

The waveform drawn on each clip shows how loud it is, with its level and fades applied, so you can see the effect of your changes.

To mute the camera's sound of all clips at once, click the M box in the Camera mic track's header (or External mic's).

Two microphones

With an external microphone, each clip has a clip on the Camera mic track and one on the External mic track, and the Audio tab shows both. Use both, for example your voice from the external microphone and the engine from the camera, or mute the one you don't want: in its section, or with the M box of its track to mute it for every clip.

orbis-reframe tells the two apart by their order in the file, which is how the X5 records them. If a track ever sounds like the other microphone, listen to both and use the one you want.

Projects from earlier versions

A project saved by an earlier version of orbis-reframe is converted when you open it: each clip's sound goes onto the Camera mic and External mic tracks and keeps its level, mute and noise reduction. A recording you didn't use is muted there, so the project sounds as before. A microphone you had put on an audio track yourself (Put the other mic on an audio track) moves to its track too, keeping its level and mute; the track it was on goes if nothing else is left on it. Saving the project saves it in the new format, which earlier versions can't open.

Noise reduction

Each audio clip, the camera's sound included, can have one kind of noise reduction. Pick it under Noise, and set how strongly it works with Strength. Picking a mode sets its usual strength.

Mode What it does Use it for Default strength
Off No noise reduction.
Wind reduction Turns down wind noise, and keeps voices and other sounds that stand out above it. Walking, cycling, talking outdoors: wind without an engine. 70 %
MC: Wind reduction For motorcycles. Follows the engine's pitch and keeps its sound, and turns down the rumble around it, wind most of all. Road noise stays. Riding, with the engine as part of the sound. Works best on a microphone that's sheltered from the wind: it can't dig an engine out of a microphone the wind drowns. 70 %
Hiss / hum Turns down steady background noise (hiss, fans, air conditioning) and mains hum, and keeps voices and anything else that comes and goes. Quiet scenes, indoors. Not for riding: a steady engine counts as background noise too. 50 %
Voice only Keeps speech and removes everything else: engine, wind, road, music. Talking to the camera while riding, when only your voice matters. 100 %
Voice + ambience Keeps speech and turns everything else down evenly, so the scene can still be heard. Talking to the camera, keeping some sound of the ride. 50 %

Noise reduction applies to playback and the export. Listen with it on and off to choose; more strength takes out more noise, but too much can make what's left sound thin or watery.

The voice modes look 3.5 seconds ahead in the sound, so jumping to another part of the video takes a moment longer while one of them is on. They need ONNX Runtime (libonnxruntime1.21 on Debian 13, libonnxruntime1.23 on Testing and Ubuntu 26.04) and a speech model that comes with orbis-reframe. If either is missing, choosing a voice mode says so, and the clip keeps its previous setting.

Lining up a separate recorder

Sound from a separate recorder (a phone, a voice recorder) doesn't start at the same moment as the camera, so it has to be lined up by hand:

  1. Add the recording to an audio track (Media ▸ Add audio file…) and drag it roughly into place.
  2. Find a sharp sound that both recorded: a clap, a door, a word.
  3. Zoom in on the timeline (Ctrl+ mouse wheel) until you can see that sound in both waveforms, and drag the clip until they line up.
  4. Select the clip, and fine-tune with the arrows of Start in the Audio tab (10 milliseconds per click) while you listen.

Clapping once in front of the camera at the start of each recording makes this much easier.